Exploring Basic Plumbing When You Install a Bathtub
Exploring Basic Plumbing When You Install a Bathtub
Blog Article
Just how do you feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is additionally a moderately tough task. If the old tub is conveniently easily accessible, the job can move easily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will require a helper to leave the old bathtub and also set in the new one. Ensure you have certified yourself for the work as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to think about employing one before you start. Chances are you may need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually already gotten a new bathtub and don't need to change the plan of your previous water system pipelines.
Your tools as well as product list should make up the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bath tub in the required placement. The wood boards are handy in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub until the spirit level checks out degree.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Switch on the supply of water and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bath tub ought to wait till the bath tub has actually been made use of a minimum of once as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in area between the tap and the sink. Protect the faucet in place with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The previous type needs to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, leading to difficulties with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes as well as cartridges, as well as can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can crack rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is advisable to fit the floor tiles using waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I ran across that blog post about A Step-by-Step Guide to Installing a Bathtub when scouting around the search engines. So long as you enjoyed reading our post kindly do not forget to share it. Thank you so much for taking the time to read it.
Services Report this page